Search results

I have an older Raypak propak type water heater in my equipment room for my car wash - have been using a Johnson Nema A19 stat fr the unit - mainly on off run it from 50 deg water up to 110 degrees as needed - noticed it went bad on me this year - is there any suggestion for a stat that is both...

hello - Does anyone have experience with this unit from Kleen rite? - What is the impression - how many selections how many items can each selection hold? How reliable is the unit - any major issues or concerns?>

Have had a hard time finding a high security outdoor vendor that is NON REFRIDGERATED - I am only looking to vend auto care products do not need refrigeration. It seems like the ones I have been coming across are very expensive and all have some sort of cooling capacity for beverages. Etowah...

Hello - Just looking for advice on best place to install a car wash camera in my SS bays - is there a good place to get a layout of this for a 6 bay ss? 2 bays on each side of equipment room? My biggest question is do we install above the Meter box or directly on the other side of the meter...

Hello - Have been using Hudson valves for high pressure floats / Water Rinse tanks for self service - however when they fail it is catastrophic - is there a better solution in regard to float valves that is recommended? I believe at this pint would be fine with a slow leaking valve over time -...

Hello..I am using microcoin ql and mei bill validators..is there a way I can wire crypto pay to read the pulse of both the validators and coun acceptors in my ss bays and vacs in order to capture myntotal cash and coin counts as well as my cc?

Hello - is there a number for Dilling Harris or someway to contact them - I have a vendmaster older unit - that I was hoping to possibly get an upgrade kit for / adding crypto pay etc so that I do not have to buy an entire new unit for replacement - Any detail would be appreciated - also - is...

Hello - I have an older 40 foot straight tube nat gas heater I need help with - Ultimate is long gone and there is zero information on the unit that tells me anything about the heater itself - mainly BTU's - is there a company that can cross reference old ultimate heaters by serial number?

Just doing some general numbers and think through in terms of Tunnel investment - existing established business. In general is it fair to say 50% of Gross Revenue in the Tunnel business goes to Overhead? Keeping debt service separate from this number.

Hello - is anyone using Blendco super clear successfully in a Self Serve scenario? I have a 7 bay where my were costs are outrageous. I was thinking to use the reclaim for wash water and weep water It could be a winner for me - what have people experienced with this product? The downside might...

Hello - I am not too familiar with Modwash but I understand their push of course is clubs / unlimited. They seem to be on super fast aquasition build mode. Word that they will be building within 5 miles to a car wash I have an interest in. What kind of revenue hit could be expected / and...

So thinking of adding Crypto to my vac's - What are the forum's thoughts on adding this technology to vac's? Currently - $1.00 = 4 min w/ Quarters Using a Kleen-Rite 77406 Accumulating Vacuum Timer, 110V Could I use this same timer to go to: $2.00 = 8 min w/ Credit Card #1 -Can the same...

Hello - I have been using the following - Honeywell Modulating Temperature Controller T991A1061 Remote Bulb 160 to 260°F Analog Heat Only These have been problematic for me as every year it is a hit or miss with the thermal sensor - will it read 38 degrees this year when set or will it...

Need some advise on how to repair a JE Adams machine - The wire rod that does from the top of the towel bar down to the acceptor where does that fit into the coin mech? Is there a manual for these online somewhere for those directions?

Hello - Have any experienced breaker tripping to the point that you lose HP on a cat pump. All functions work except you lose high pressure. When you go to switch the breaker off then back on - you regain pump pressure - Is there an overheating issue I should be concerned with, or is it merely...

What is best recommended for swivels on HP hoses - have run into an issue where low pressure applications swivel leaks - High presser soap / rinse the swivel seals fine.. Does anyone have a really good go to swivel they recommend for HP gun applications that also operate low pressure functions?

See picture attached- I believe this is both an RO / reclaim system - please correct me if I am wrong - does anyone have detail on this system or know where I can go to gain more information on what exactly I have here?

Hello - Any recommendations on paint / brand and type to use on FRP wall board for car wash bays ? Has anyone had great success in this?

Is it best to use the (B) input on a Weepmizer for a Foam Brush Change over - or - Have an independent Stat? I have had issues with bulb style independent analog dial stats - Would it be recommended for a digital stat? To help set exact adjustment?

What is best brand / type / That has been successful in a below grade RO tank