Recent content by acbruno

Definitely worth it. I have one on my foam brush for past three years running 24/7 no issues. I have anther one in operation for two years for my desalt/bug solution no issues. I can't run my tire cleaner or winter foam with one because the dilution ratio only goes to 50:1.

I have seven boxes. I can sell a couple unless you want all seven for spare parts or to use in your vending area or vacs. Let me know.

A customer discussed with me his concern about our SS using non-heated water for high pressure rinse because he said it freezes on his car by the time he goes to dry it. Temps were around 10 degrees F at that time. We have four high pressure functions (soap, wax, clear coat, and rinse) and only...

I have a wood trough that runs to 4 bays one one side from the ER and another 3 bays on the other side. It is 16 inches wide by 8 inches tall and has plenty of room I added foam insulation a couple years ago. It works well but I have to service the lines so much, the insulation has been damaged...

I would sell any or all components. I have all the equipment for 7 bay plus some spare parts. Let me know specifically what your looking for and I'll get it pulled.

I removed my WashGear equipment and replaced it with WashCard this year. I have 7 bays with the CardMate II terminal box, controllers, serial mate interface modules, wiring, and many spare parts. I'm willing to sell it all if your interested. How many controllers are you looking for? Tony

I have had two problems with hydrominders this year. Both are the standard 511's without the bead breaker snorkel and both are new. The first failure was with the winter foam brush solution tank I added this year to switchover when the temp drops. I came in the equipment room one night and found...

You could put the fix-a-leak in your system and bypass the heat exchanger while you run if for a day or two then purge all the liquid from your system and replace it with new.

Seemed to have worked for me for now.... I bought a 32 ounce bottle of this stuff from intheswim.com after talking with a guy from the manufacturer. He recommended mixing the contents with an equal amount of glycol/water before introducing it into the heating system. That stuff is very thick...

I am looking at increasing my prices too. Right now I have my pricing set for $2 for 4:00 minutes which is one quarter for 30 seconds. It’s been this way for 8+ years and all my competitors have gone to $2.50. I’m thinking it is time for me to increase prices as well before the busy season. I’m...

Yes, I do have cold rinse. The only functions that are heated is the soap and wax. I spoke with Navien about the error code 39 flow sensor shutting off water flow. They told me what set of wires to pull from the circuit board to prevent the water shutoff. After I did that, I haven't had another...

I have two Navien NR-240 tankless on-demand water heaters that lead to a holding tank feeding 7 self service bays. The incoming water pressure is regulated to 60PSI and passes through a water softener first before going to the water heaters. Problem is, during moderate use, one of the water...

I attached a side-by-side picture which has the picture from the customer then one of the front of his vehicle as he was exiting the bay. My first question to him will be if he is positive this damage occured during his wash at the car wash. I should be able to see some type of blemish in the...

After writing a few paragraphs, I decided to make it simple. Here's what I wrote back: Luke, thanks for your email. I pulled the video of your wash on July 6th at 7:30pm. If you would like to discuss this further, please leave me a phone number and a good time to call you.

Here is a couple pics from the bay he wash in I just got done viewing the video from this guys wash. He was only a few inches from the paint surface at times. I could not get video from the spot he said the paint came off because he parked too far in the bay. Here is a couple shots from my rear...