Search results

I agree with you people buy coffee,breakfast sandwich,donuts and gas every day never once do they realize the price change. We don't change our prices for years in the SS business even though all of our expenses have sky rocked. I raised my bays $2.50 for 4 minutes. If they don't like it...

We finally fixed our issue thanks to the great technical support of PDQ. They instructed us to deinstall software and delete a file then reinstall the software using a flash card reader. Making sure the correct IP address put back on not the factory default.So far everything seem functional...

yes we always use two computers daily one PC in the morning and the lap top directly plug in to JO during the day. Looking to work on it this weekend snow expected Saturday evening.Also tried different ports

As soon as i figure this out i will post what we have done.I don't want to try anything software related just in case i put the laser m5 down. As long as i'm able to wash cars I'll wait a bit. Thanks for your interest

I've tried multiple IP addresses I get timed out going to try to reload software so as i do i will report the out come. Laser works fine looks like we should be washing cars with the snow and salt don't want to take a chance that i take down the wash playing around with the software. Thanks for...

I`m not to good on a computer but when I turn on my computer I click on the icon set up for the Laser. Then I get page cannot reached IP address 192 168 55 101. I have also tried a different port inside the JO ?

When I try to sign in to connect to the Viper board inside the (JO) it will not allow me anymore. Normally every morning i log in to check on daily counts.M5 works perfectly just cannot make a connection. IP address is correct changed cable,different computer with correct IP. Any suggestions? I...

Thank you Kris I will check the output card. When I do I will get back to this site.

I was wondering if anyone knows what turns on the rail heat my weep turns on and off. Is it also controlled by my bay temperature probe?Heaters work when bypassed can't get contactor to close. Thanks Liberty

APM I put a skim coat on my floor in the bay underneath where the Laser would be as car exits. Problem solved there was some aggregate showing on the concrete with the skim coat it filled in the voids in the floor. Thanks for pointing me in right direction. Mike (Liberty)

Thank for the info I think i may have figured it out also i have noticed that my floor concrete is not looking smooth pebbles and stone are protruding. Wondering like you said maybe the ultrasonics are not giving a true reading and signal is bouncing in different directions thinking there is a...

I am having a problem with the M5 when the wash is completed the wash does not go back to its home position. laser stays up front need to reset machine then all is fine. It does not happen continuously Error code says stuck in bay exit outside eye 1 sensor on. any info would be appreciated. The...

I replaced contactor today terrible weather i will get back to you when i start washing cars.

Thanks for the information. I will check in the morning and get back to you.

Having problems with my Laser 4000 with motor run on it seems to be happening in the same two locations each time. Wash will start as usual go across front of car down the driverside arch turns to do rear of car and stops there no movement,the stop light indicator goes blank and the Laser needs...

I changed top prox on the bridge that reads end of travel for the bridge I was then able to move bridge in any direction.Seems to be working properly thanks for your response hope thats it electronics can drive you crazy.

Checking prox i will check in morning and get back to you thanks for response

I have a pdq m5 i am have a error that says illegal move extent when trying to move bridge from rear of car to front.It will not allow it to move i can move it any other position.Any suggestions?THANKS MIKE LIBERTY CARWASH CHICAGO IL.

Like to thank mike menard from pdq for solving my problem .it was the high leg on the input to the abb speed controller.i removed wire and ran it with single phase problem gone. Thanks mike. Mike liberty carwash

I'm still having intermitten problems with my Laser 4000 stopping while washing cars .Lately read out is arch rotation error.and a fl2 on speed controller only when you try to reset at joy stick.I you look at ABB display its 00 than try to move in any direction goes to fl2.but it will not allow...