Search results

The green button to go to error code list and totals no longer works. May be in the display or cable as wiggling the cable ends makes the unit reboot and run hydraulic pump briefly. Anyone have an old 5000 pump stand with this panel on it?

replacing the gantry on my trusty 5000, isn't quite plug and play. Seem to have a prox switch or pulse wheel prox issue. On the first presoak pass the gantry moves forward, stops reverses and goes to bottom of rear and shuts down. Is the range of travel controlled by the pulse wheel counts or...

My led displays are not visible in daylight on my IVS vacs. I have some spare D&S vacs that as I recall had nice bright displays before I salvaged from a wash I dissassembled. both are BT912, but the ones in my IVS have a dash -IVS and the ones in my D&S vacs have -D&S. curious if anyone...

the tri foam chemicals in the mixing tanks on my D&S 5000 have recently started to jelly/slime. A week ago my pink was barely coming out and I discovered 2" of jelly in the bottom of the pink and yellow mixing tank. Blue was much cleaner only a little slime. Been running a couple years so I...

Last night wife asks if there should be foamy water on the floor of the equipment room.... turns out my low pressure presoak pump is leaking where pump and motor meet. Guessing its the pump shaft seal but neglected to ID the model of the pump while I was at the wash, only ID i could see was...

Have a 3 bay SS with 3/4" service. A customer stopped me about a month ago and said he and another customer were using the wash just fine. Then a third pulled in and when they were all washing, all 3 bays lost water pressure. I have a pressure gage on the hot water to my supply tank feed that...

My wife and I have recently finished a month of updates to one of our washes, new FRP panels in all the bays new signs and paint (which lasted less than 3 years since we bought and renovated the firs time). Anyway, we have started arriving at the wash to find the air compressor breaker (in the...

not seen this before. customer left the bay and the LED 6 was just displaying -ON- not time left. He was a token payer not on credit card. I was afraid to leave the wash with a bay turned "ON" not counting down so I hit the reset button on the back of the LED6 and it went back to normal. How did...

OK twice I have been called to one of my washes with a dreaded "there is green fluid running out under your door". First reason for this call is this particular wash never had a floor drain in the equipment room.... However in both cases I arrived to find my tire cleaner tank overflowing with...

Im using what was left over from prior owner, its time to get something to restock. Since the dial says "wax" and based on the scum layer that was in the old tank system I replaced, I think it really might be a wax, but not seeing a lot of choices for a "wax" to go on at high pressure. Have...

My 5000 is not turning on the power blasters when it goes down the front (washing the grill of the car). and the side spinners and power blast are coming on 2/3 of the way back rather than as it transitions to the downward slope. Its as if it wants to be homed close to the entrance of the wash...

Since I have already had one break in at this wash, I have decided on tokens for the changer. (it was empty and not yet in service when they broke in so they just took my camera recorder). Anyway since I wont be selling quarters, it makes little sense to take quarters only in my mechanical drop...

FInally getting close to opening my second location. Bays have bill acceptors, Cryptopay, take quarters or tokens, the vacs take bills, quarters or $1 tokens so I changer will not likely get used much, but I am thinking of setting up with $1 tokens. the manual I downloaded from Hamiton says the...

recently I have had a couple calls (yes, have my personal cell phone taped to the auto cashier, still a noob) Anyway the written instructions from D&S say to deposit money and pick a wash. the vocal direction from the lady inside the goldline says "please make a wash selection and enter your...

Installing a used Air Logic triple foam panel located some distance from my main control boxes. It has its own 120v input and its own 24v transformer which powers its programmable control relay and switches the 24v from the main control transformers to the solenoids for each bay and possibly...

Bought some used meter boxes off ebay and getting ready to install them. there is mortar where they were bricked in before, and a yellow film (wax maybe, like my walls have). My research indicates muriatic acid, my first thought, might damage the stainless so looking for alternatives. Anybody...

had a weird one this weekend. D&S 5000 wouldn't start for customer. got there and put in manual bypass, gantry ran toward the exit. Checked some voltages from the front and back eyes, both leds on prog. controller glowing but dimm. Turned back to manual override, all OK, go out and move gantry...

My D&S 5000 is home at a spot of weld at the arch about 1/4 in from the enterance. I have noticed another spot about 1/4th from the exit. When my top wash cylces, it sprays presoak from the start, forward, then all teh way to the back and then again to the front so the front 3/4 of the car get...

I changed the 2 bay manifold valves to 3 bay, and while wiring, noticed each bay has its own input to the smart relay. If I wire 24vac to the third input terminal on the relay so it energizes when the 3rd solenoid is powered (same as bay one and 2 are already) will that work or will I have to...

Replacing the tank system on our second wash. I have hot water plumbed to my Etowah valley low pressure tank rack. The pumps are fed from both sides of the manifold/head. one side has a solenoid valve wired to the rinse cycle, this side also has the lines feeding HP soap and HP wax. I do not...