Search results

Does anybody know where I can find tapped stainless pipe to mount individual solenoids? Building a low pressure system and want to attach the assembly to the pump plant. Basically, i’m looking for a length of stainless that i can mount 8 solenoids. i already have the individual solenoids that is...

I have a Weatherhead T-460 crimper with T-400-3C collet (3/8 inch) and yellow, green, & black rings. I was looking on KR's website for single or double braided hose that is compatible with the tooling I have. Additionally, I use "U" series fittings. Looking to replace hoses from EQ room to bays...

What would cause a Hamilton quarter hopper to randomly jam where the coin falls into the chute? It seems like the quarter partially enters the chute and then becomes wedged between the Quarter wheel and chute entrance. This results in the quarter wheel not being able to rotate until I remove the...

looking to replace a broken bill counter. looked at several models Billcon, Amrotek, and Cummins Allison. Tired of manually separating bills which means i need a 1.5 or 2 pocket machine. The cummins Allison has an extensive dealer network and seems to have good resale value but is priced the...

Check the yellow and black wire connections. A high resistance contact can cause a voltage drop under load. If you can, measure the voltage while the Sensortron is connected.

My 5hp air compressor‘s start capacitor seems to last for about a year before needing replacement (open circuit). The compressor was purchased used and I wonder if somewhere along the line someone replaced the start capacitor with the wrong size. The current start capacitor’s size is 233-280MFD...

can someone please pm the directions to properly drill a star safe head. additionally, the safe head has not been opened for at least 25 years and is rusted in place (cannot rotate safe head). Been applying pb blaster, but the head is still stuck. any Ideas or suggestions to loosen up the head?

Just installed Cryptopay and new Dixmor LED 9 timers. On one of the bays, it seems like it requires multiple pushes of the stop button (count up mode ) before the Dixmor timer ends the cycle and displays the credit card charges. I just noticed this this evening and don't know if there is a delay...

I purchased a 4k system from backstreet surveillance. Periodically, when I try to remotely view what is happening at the carwash it shows the system offline. The only way I have found to correct this problem is to reboot the NVR. Any ideas on how to solve this? Anybody else experience this.?

I have an IVS vacuum that has a round lock on the coin box. I have no key and need to remove it. thanks

Measured the current flow for each function. Current flowed ranged from approximately 800ma to 2.4 amps. Interestingly, the highest current flow was associated with my low pressure functions which used Allenair solenoids (liquid & air). The one exception was my triple shine unit which uses GC...

How would I identify that? I only see 24vac to the motor starter coil. The heater portion consist of 3 screw in coils (one for each phase) that react to excess current. Seems to be a mechanical trip.

Is it acceptable to use 22g stranded wire from the meter boxes to the equipment room? I have access to Belden 8458 (15 conductors) stranded wire from someone in the business. He got it from IDX some time ago. When I spoke to IDX they told me one of the reasons they sold it was because in the...

Installing Led 9 on bay wall and trying to minimize wires to the timer. For the Dixmor LED9, is the connection between the timer and Microcoin QL a 4 wire connection or 3 wire connection. For 4 wire coin acceptor connections (Sensatron), besides power and common, there are two signal (coin...

I ordered a couple to try out but they look completely different than what is shown on KR's website. The ones I received have a red plastic body and the control door doesn't appear to swing open to easily clear jams. The picture on KR's website a stainless steel body/frame. Did I get the wrong...

I ordered a couple to try out but they look completely different than what is shown on KR's website. The ones I received have a red plastic body and the control door doesn't appear to swing open to easily clear jams. The picture on KR's website a stainless steel body/frame. Did I get the wrong...

Mep, what size and make are the connectors on the terminal block?

Was thinking about trying out some icoin acceptors. Read somewhere else on the forum that they had issues with the acceptor losing its programming. Is this still an issue? Any experience/opinions regarding this acceptor?

Mep, what spade connector are you using for the terminal block?

Any ideas on how to mount a Dixmor horn. Don’t want to leave it dangling in the meter box. thanks