Search results

I have a tank that has a hair line crack in the threaded portion on the tank and am wondering if any one have had this problem and what they might have used to fix it short of replacing unit.

hello all Im trying to locate some wireless cameras that are 5.8ghz capable and if possible 110v powered. I have 2 installed now and want to put in 2 more on this system. I bought these about 1 1/2 yrs ago from rugged cctv and they no longer handle wireless. any leads would be great

I have a r bell cyclone automatic and im having a problem with the hose that connects the pipe from the trolly and the one coming from the commutater. The hose will blow about 1 inch from the fitting closest to the pipe from the commutater I am using 2250 psi hose with 3/4 male non swival ends...

I have a savamco model 500 table top unit and Im need a keypad unit. Ive tried directly thru savamco for the last month to get one and cannot whether the are going out or not? does any one else have a savamco unit and run into this problem or know another source for parts for these machines ?

I am looking for some g-60 ginsan timers for my bay doors.Ihave the 6x12 doors contact me with any thing you might have thanks MIKE

I have a 6 bay and when the customer pushes either tire cleaner or pre soak it will take up to 45seconds for the service to come out properly.I have 1 check valve on the line that controls both services. what times do you guys have for these services to come on?.any suggestions to make these...

hello I have some vac decals that are not vinyl but more of a acrylic type ginsan type that im trying to remove and not scratch my vac up i have tried a heat gun and that works very slow i have also tried lacuer thinner do you guys have any suggestions?

I have been working on pinpointing down a leak that i have in my floor heat and we have found that the leek is in the header that feeds the system.This piping is under ground directly behind thd equip room.I have a box on each side of the equip room that control bay 3-4 and 5-6. I was thinking...

I have a mineral tank on a water softner that where the head screws into the top the threds in the tank are cracked. When the head is screwed on the unit will spray out the side. I have put a sealent on the threads, srewed the head onto the tank and put a 2 part epoxy around the head and the...

Im trying to find a device that will tell me when i have single phased power before i burn any motors. Last nite i had a power outage and all seemed fine but i found out i had lost 1 phase of power. That was not untill 2hrs later.but all equipment was running.

I have a bay hat will shut of and the time still runs you go back to the coin mech and push the service you were on and it will run for 30-40sec and does it again. I have switched the coin mech door with another bay and that didnt help i have switched the 24volt hot wire to the bay, switched...

I have a flat style roof and presently have all my high pressure and low pressure lines run in a sheet metal type trough on the roof.It has a removeable top every 12ft well after 23 yrs the bottom of the trough has rusted out and looking at replacing it and was wondering what anybody else uses...

I have a 8 bay wash that has the plastic hose for the floor heat in it and presently have 4 of the bays floor heat shut off on the return lines.My fluid level dropped so the boiler would not come on added 14 gals of fluid to bring back up to level.My question is is there a way to test to find...

hello i am getting ready to order new chain and rollers for my conveyor and looking for opions on different chain and rollers. I have a 90' conveyor which is a sonnys over/under. I do run the 7'4 spacing and that has worked great for me. also looking for anyone that has put in the retro kit...

its getting colder and it brings up a question. if you have a freeze up what is the best method to un thaw. I have a tin trough that sits on top of the roof and then the high pressure hose goes down into the boom thru the roof. we use 2 methods 1 is hot water in the trough to thaw it 2 is a...

I have a vac that will work on and off at times. it has the microswitch coin acceptor. i have replaced the switch, have also replaced the timer. motors are good. what will happen is customer will put money in it and it does not startsometimes you can hear the motors acting like they are going to...

I had a customer come in and claim the foam brush left blue spots on the mirrors and on the glass on his car.The product is ran thru at 70-1 thru a hydrominder. i have had this product on line for about a month and this is the only problem i have had. Ive tried all the cleaners alcohol,lac...

I have a problem now and then with a roller going down backwards at the exit end of my tunnel. When this happens it will jam up the conveyor and you have to manualy pull the chain back and pick the roller back up thru the trap door and put it the right way.I have seen it happen when the car...

having problems with a pump with no pressure at the bay but it has pressure at the pump on the guage. I have changed the unloader,gun&wand at bay,checked for leaks going out,check valve on incoming water line,changed incoming waterline (colapsing) checked check valves in pump head,fittings have...

I have a dema injector that has no draw it is getting a good flow of water thru it but will not draw product. took apart and is clean inside both the water flow screw and the chemical draw adjustment screw are open all the way and still no draw.any other suggestions to look for short of...