Search results

Are the MEI bill acceptors repairable? If so who does everyone recommend? Thanks, Vic

Kleen Rite is out of stock until next week on the Viton kits. So I will order a few with the Dema valves and try. Thanks Again

Check out your special fees with Worldpay I was getting zapped for PCI compliance and some sort of BS $30 fee and month. I called them set up PCI compliance and removed the BS fee?? My worldly charges dropped significantly.

Sorry.. $400 each... But I kinda like the idea of the stop button with 2.5 times the charge. I charge $2.00 for 4 minutes. So the max would give them 10 minutes at a charge of $5.00.. Or they can press the button to end the charges. I feel most people need more than 4 minutes and then have to...

OK THANKS.. Now swiper with or without button? Opinions?

That's great. I was just about to say to check the T bar. The arch arm should only fault out at 30 degrees. You can lift it and see when the eye makes contact ( light comes on).

Sorry if this has been discussed before. But with the market going to more CC and less cash, would it be worth it to invest in the $1200 ( 4 @ 300 each) for the crypto pays for the vacuums I already have them in the wash bays and can't be happier? Opinions? Thanks, Vic

I don't know if it applies but check my post about the Carlo Gavazzi sensors. Seems like your having the same gremlin I had this past weekend.

Just my 2 cents.. I have a 16 year old wash world HV ( I believe it is very similar to the LW4000) it has been a great unit. There are some tricks and parts that break ( wear out) but to be honest I can't justify the expense in a new unit now. But having 2 self serve bays and the one IBA. I...

I'll send you a UPS label if you message me with your address. Thanks. Vic

I use mine all the time for leaves, and just general clean up. I have a battery powered unit. It is a green works 60 volt. I wouldn't be without one.

Thanks can you get the VITON Daiphragms from Kleen-Rite? If so, do you have a part number? Thanks

Had a gremlin for a few days where sometimes the wash would not see a car enter and timeout. Watched the camera and you could see the car pull in and it never told them to stop. Sometimes it would work, BUT then it would try to remeasure after the TF was applied when it went to rinse and give an...

I have seen the LP 1 or LP2 takes a long time to get to the outside unit and the line is full of plain water. I then just disconnect the outlet hose right after the solenoid and if water is slowly coming out the valve is leaking. Just the 50 psi of city water in the line will show the small leak.

Anyone ever use a replacement for the Danfoss 3/8" water/chemical solenoid valve on the wash world HV system. Seems like the new ones only last a few months and then the seat has a small crack or wear pattern and you have to replace the solenoid. This would be used on the LP1, LP2, triple foam...

They are American Changers and you can set up the anti-stringing inside the programmer. I also use a simple timer to cut them off at night. I also set-up my Hamilton Gold Line for my IBA to not give a refund. Sorry if you put the money in, you get a wash. Eliminated that stringing issue also...

Also my change machines shut off at midnight and back on at 5-6am. They can use the CC in the bays if needed that late at night.

On my machines I just have it set up for one $20 then it shuts down for 30 min. Ended my problem with stringing also.

Hey guys. Just wondering if anyone has a manual for this unit. I have tried WASHWORLD and they don't have one. Also where I can get the membranes. Thanks again for all your help, Vic

So MEP and Sooner with these BS fees gone the rates aren't that bad, still uses dial out. Really never any issues except for the occasional no batch, ( which is easily fixed and Hamilton does have great service over the phone) and the idiots putting coins in the CC slot. So I'll just leave it...