Search results

Try putting a smaller tip in the gun just to see if the pump is capable of higher psi. If you get more thank 900 psi it’s probably not the HP seals. Did you change pulley sizes?

What is the Bots purpose? What are they trying steal?

Mine are on a WSII. I also had another issue but I don’t exactly recall the circumstances. If memory serves me correctly I had a relatively new swiper that was rejecting almost all cards. After calling tech support he was able to see that the cryptotap was messed up causing the issue. I’m pretty...

I've had two Taps where the first Blue light that is normally always on stopped working. If you tap a card, the remaining lights will flash and the unit still works. One I sent back for warranty repair, the other I just rolled with.

I have to say I was impressed with the Takagi’s today. Last night we lost power at the wash and the power company didn’t get us working again until about 10am. When I fired them up the incoming water temp was 37° and the output temp was 121° with a combined flow of 7 gpm. 2Biz would you change...

Thanks for the explanation 2biz. I finally got my hands dirty with a Takagi. I’m using two 199k units in parallel fed by two Taco 013’s in series to heat water held in a 120 gal storage tank. Units are set at 120F and my tank aquastat which controls the pumps is set at 115F. Have had it in...

I can imagine! I'm not sure if Oasis has changed this aspect of the machine but ours circulated heated anti-freeze through all the rails AND through the spray arms. Like I said, our Typhoon was 20 years old and the high and low pressure spray manifolds weren't separated back then. However, the...

2Biz, just out of curiosity, what is this 30 minute timing cycle and what is dictating the percentage of on-time/off-time? I thought you were simply controlling flow to your heaters with the Aquastat once the system is powered up at 32F, flow to heaters at 55F until return temp reaches 70F?

I just retired a 20 year old Typhoon last year. It was a great machine but then became a maintenance nightmare. Having just gone through a brand new Typhoon install last week I would say the build quality has greatly improved. The zero degree nozzles are impressive but I wonder how often do...

How is the bottom of a vacuum motor a danger? Is the 13 year old going to disassemble the motor and stick their tongue in the hole? You better make sure to never prop open your equipment room door…a toddler could wander in there and get dismembered by a motor pulley or guzzle some tire cleaner.

Was reading the latest Kleen Scene and noticed a new float valve by Cleveland Float being advertised. Sounds like they copied a LOT of features from the Jobe Topaz valves which I use. The Cleveland S5-100 has high flow and handles high temp water for less than half the cost of the Jobe Topaz...

At one site I was using output 2 to turn on my IBA floor heat at 35F. This particular weepmiser would 'bounce' at 35 and the output would come on and off, not really good for a boiler or an air compressor. The weepmiser isn't supposed to do that but this particular one did.

I wish the website was just difficult, I found it to be impossible! Maybe with repetition it would have gotten easier but I never got my Nayax units installed because of other reasons. The website interface is truly overwhelming.

I’ve found my answer…they wire into the Bay node…x404.

We are reinstalling two M5's we removed last year from one of our other sites. The site they're now in has Wyndstar doors on the exits and their photoeyes are wired into the Wyndstar motor/controller which is a pain in the ass to access and and work on. It was easier to simply mount a new set...

We would like to wire in a set of photo eyes so when a customer drives through the blowers too fast it will kill the remaining dryer time on our M5. Can anyone tell me where the signal should be wired into? I’ve looked at all the various inputs and none of them sound exactly quite right. Thanks.

Mep, are you talking about Cryptopay or Nayax? I have Cryptopay on some ACW 4/5’s, a Goldline and two WSII’s. I’m was inquiring about his Nayax setup.

Do you have a link to the kit? How does the operation work...is there a specific sequence customers must follow or can they tap, then choose wash or choose wash then tap? Do they have to choose the wash on the Nayax unit or can they use the acw buttons? How does the transaction show up on...

Eric H which burners were plugged up? Were they on either side of the pilot? I just had this issue with my Raypack. When the main valve would open I was getting massive roll out so I figured the heat exchanger must be sooted like your friends. In my case, the pilot would light, thermocouple...

I don’t remember the specifics but I did have a customer say he was charged by my Wash Select with Cryptopay (don’t know if it was a swipe or tap) and he didn’t get his wash because the customer ahead of him put it out of order. They wanted a refund but I could not find any transactions on my...