Search results

when thru conversion, had 250 MH, converted, bought us made units , because we need to service units in the future, about 6 months old , the output is great, units are ( believe) are 64 unit leds. was warned not to look into fixture when lens was not installed, they are that bright. happy with...

220 or 120 makes no difference, what is needed is that all grounds be it metal case tied to system electrical ground, it appears that there are separate returns which indicated by voltage differences. electrical system if its 220 or 120 all 24 voltage's must be the same, if there are voltage...

thought about your problem, trying ungrounding meter looks like your using 220, may be a problem with ground loops isolate each bay electrical system by eliminating ground wires and see how system operateds

may be floating grounds, check for voltage differences between grounds of each system, recommend slow blow 4 amp fuses, 7 amp improper size for 100 va transformer, coin co vantage units in our view are junk units( nothing but trouble) , check cable runs 24 volt power needs current to meet power...

that's what we try to do, there are a few who have an attitude that is different from the norm, this is when the police get involved, what criminal terms or wording could be used in describing to police what we want done. Need to be polite and professional, physical force wont work with these...

what type of complaint can be filed against a person who washes his car in the bay and then refuses to move as they dry and detail their car in the bay and won't move. Lately we have had this happen several times with customers waiting to use the bay and we have had to have the police show up to...

he's not kidding , time to up grade

air shamme deleted the dump valve, for simpler system , air flow with a by pass for gun shut off , units need air for cooling. each motor is about $45. tried just replacing brushes, did not last long so now we just replace 3 motors at one time and throw away the old ones. 2-3 years of heavy...

we have had 2 very major electrical shunts in last 6 years at two locations first shunt occurred when one wire broke on a SCE power company transmission line broke and hit a vacuum with 11000 volts, causing a back feed thru the vacuum. thru the 3 phase in the transformer blowing it up and...

check neutral and wire grounding thru out car for ground loops, stuck valve, switch may be going bad. sounds like one the head beater problems

take a close look at the crome sleeves in the sun lite if there are any scratches on the sleeves throw them away scratches will led to suction problems & damage the inlet seals and don't skimp on the little O-rings.ok to reuse Teflon back up rings if not bent. it is a lot cheaper to it right the...

check the 2 little o rings and Teflon back ring on the crome shafts, use silicon o ring lube when siding crome sleeves on so they won't get nicked. water is pushing past o rings.

ica and local shows are we buy equipment and lots of it, any ware but Chicago, will miss show first time in 20 years. any body who goes to chicago have at it.

found factory assembled problems in lose ground wires, found cause for a $ $800 board failure, a wire that dislodge itself and poped out of factory assembled connector that controls shampoo head, some connectors were pull and plug ( about 12 connectors) on board, others were very hard to...

adams response was go to hell

when trying to trouble shoot, found information provided by adams to be poorly presented, schematic provided is useless and income pleat , trouble shooting guide is useless, some information was generic in nature. plastic nuts on hoses very weak, fuses holders on vacs break when vac motors go...

surprised on how easy it is to damage a adams combo vacuum. some one pulled on the shampoo hose while it was on the hanger. resulting damage occurred when the hose pulled out of the shampoo head, which is held in by a weak plastic connector. pulled control wires and supply hoses out of unit...

quite a few years ago we moved all meters to out side of bay meter is fully enclosed in block work, was expensive, but now our maintance has dropped to a very low level and we also have bill acceptors installed. water damage is no longer a problem.

make sure you can buy replacement parts like lens, like a glass lens,. . Lithonia is a brand we have bought. any light that spares are not supported are not worth the cost or problems. Once led die its nice to know that is easy to repair. Also failure mode for a led is a short, not a open. We...

led replacement am in the same boat our led 250 hw are old, it was easy to just buy some led 60 leds new fixtures then it was to update housing, its not only the cost but also dealing with old housings dirty lens old gaskets and we repositioned some lights . new lights were easy to install...