Log in
Register
What's new
Search
Search titles only
By:
Menu
Log in
Register
What's new
Search
Search titles only
By:
Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
Waxman's latest activity
Waxman
reacted to
Greg Pack's post
in the thread
New guy
with
Like
.
carwashfng a couple of initial thoughts: 1)Rip off all the bay signs and order about 15-20 gallons of Arcadian Nu wall or Quest...
Yesterday at 4:14 PM
Waxman
replied to the thread
Floejet pump
.
I manually drain my compressor 6 days/ week through the ball valve at the bottom of the tank and also through the ARO water separator on...
Yesterday at 4:11 PM
Waxman
reacted to
PaulLovesJamie's post
in the thread
Floejet pump
with
Like
.
Its possible that your compressor is the problem, or contributing anyway. I've observed that as they get older they produce more water...
Yesterday at 4:07 PM
Waxman
reacted to
Car Wash Man's post
in the thread
Kondor KL2 Carriage Jam Fault
with
Like
.
Carwash is back up and running after repacking the bearing!! Thank you everyone for all your help, greatly appreciated
Yesterday at 4:06 PM
Waxman
replied to the thread
Kondor KL2 Carriage Jam Fault
.
Usually bearings aren't proprietary in my experience. You have to take it apart anyway, so when you remove the old bearing, get the...
Yesterday at 9:15 AM
Waxman
reacted to
Timmb's post
in the thread
Kondor KL2 Carriage Jam Fault
with
Like
.
What makes you think they aren't making good contact? The whole weight of the carriage is on the rollers. Are the rollers spinning and...
Tuesday at 6:21 AM
Waxman
reacted to
washnshine's post
in the thread
Looking at leasing my first car was. Thoughts, opinions, advice?
with
Like
.
Hard to say. I don’t know the volume of people that use the exit you are on. Also - where are they going and are they in too much of...
Tuesday at 6:19 AM
Waxman
reacted to
washnshine's post
in the thread
Looking at leasing my first car was. Thoughts, opinions, advice?
with
Like
.
Do not assume anything will work after sitting that long. Find out what type of IBA you have. It does not sound like that was...
Tuesday at 6:14 AM
Waxman
reacted to
Dan kamsickas's post
in the thread
New Car Wash Owner Questions
with
Like
.
Not trying to be rude but if I had a 5 dollar bill for every time I have heard a similar sentiment from someone looking to get into the...
Tuesday at 6:08 AM
Waxman
replied to the thread
New Car Wash Owner Questions
.
I would also suggest getting a part-time job at this car wash that you're describing. That way you can get an insider's view of the...
Saturday at 6:15 AM
Waxman
reacted to
OLFOT's post
in the thread
Busy Day - Detailer sets up shop
with
Like
.
Da nerve of some people! On occasion I have to run off a detailer trying to set up shop at one of my locations. One time there was a guy...
Friday at 3:54 PM
Waxman
reacted to
Randy's post
in the thread
Floejet pump
with
Like
.
I don't have any air dryers or filters on the air that is supplied to my one and only Flo-Jet pump on the Foam brush system, never have...
Friday at 3:31 PM
Waxman
reacted to
Greg Pack's post
in the thread
Order of your Passes
with
Like
.
I don't know the specific simoniz products and that would be a good question for a simoniz rep. Personally, I'd want to stay away from...
Friday at 6:55 AM
Waxman
reacted to
HeyVern's post
in the thread
new car wash equipment idea the belt brush
with
Like
.
I guess they call it a Short Story for a reason
Apr 18, 2024
Waxman
reacted to
Greg Pack's post
in the thread
best water resistant glue/contact cement for air shammee
with
Like
.
I've used goop or similar contact cement and it seems to hold up ok. I tape it on with painters tape until the cement dries, then...
Apr 18, 2024
Members
Menu
Log in
Register
Forums
What's new
Log in
Register
Search
Top