Search results

hello all, does anyone have any experience with a bad counting wheel? My water wizard is initiating different cycles at the same time in the middle of a wash. My counting wheel has a little play in it and when I run it up and dwn the track the prox flashes are not consistent. Coleman only item...

Hello all, The presoak on my WW 1.0 doesnt start coming out until it is over the hood. Could there a solenoid problem somewhere? I havnt seen any leaks anywhere either. Any suggestions wold be greatly appreciated. Thanks John

My MEI CF7000 will not accept quarters. It says unknown coin. Can someone help me with this issue? Thanks John

Ok guys, I get broken into about once a year. The thieves use a crowbar and punch through the bill accepter to get leverage and pull door open every time. It used to be a single bay but now they are hitting multiple bays. My question is would it be better to just not have bill acceptors and...

Silly question guys, what tips go where. I bought all new tips and noticed they are all over the place. Thanks for quick response. John

Ok, My triple shine air is acting up. When a bay calls for triple shine the air guage drops to zero so nothing but liquid iscoming out in the bays. I put on a new air regulator and thought I had it fixed but I cant keep a constant air pressure.When the bays are calling for triple shine Its...

I used to keep my cacs locked with a traditional lock until people started breaking the clasp. Does anyone know of a metal band or another way to keep these things secure? Any ideas would be greatly appreciated.

Hello all, I have a strange problem with one of my in bay bill acceptor's. It will take a bill but wont set any time. I changed that acceptor out and I also changed the timer out and still get same result. I have never had a problem with this bay. I took the same units and put into another bay...

Does anyone have one of these? If so can I get an opinion? Good, bad indifferent. Thanks in advance. John

My RO system has worked flawlessly for the last 9 years but now I am starting to have problems that I cant figure out. My spot free water is measuring 27 ppm as it comes out of the system. I think the number should be below 20 ppm. I tried to adjust the product water/reject water with the RO...

Does anyone have any info on where to source the rod ends for the oscillators on a WW1.0? The last ones I ordered came from Texas Car Wash Supply and they were plastic. Needless to say they do not last very long. I remember reading a post awhile back and someone mentioned Oreilly's? Thanks in...

Good morning, I have 2 self serve bays where the 1034R Timer keeps saying "Please Wait' when the tire cleaner option is selected. Its like the timer is rebooting itself and will not work properly until tire cleaner is desellected. These bays happen to be right next to each other but I doubt...

Good morning all, I am currently using Harbortouch. This is one of the two companies suggested by Unitec for my Wash Select 2's. For the second time in two years they are again raising their processing rates. Does anyone have a suggestion on who they use as I may be switching companies. Ive...

Hello all, Just wanted to let everyone know that someone busted out the coin cup in my Wash Select 2. The coin cup is made of some type of cast material that is nowwhere near as rigid as a metal cup (of course not much can hold up to a sledgehammer). They were then able to go through that hole...

Hey all, Ive had to replace the decal on the meter door before and needless to say it was difficult at best. Does anyone have any ideas/suggestions to make this easier? Is the a chemical out there that will dissolve the glue making it easier to scrape off? Thanks in advance!

Hello all, My red triple shine foams and runs down the inside of the gantry on both sides instead of spraying out on the car. Has anyone had this problem and what was the solution. Could it be my procon pump getting weak? Possibly my foam generator being clogged? any ideas? Thanks in advance!

Hello all, On a set of Telco eyes, what is a good way of knowing which is bad, the receiver or transmitter? Is it a matter of just swapping the parts? After determining and replacing does anyone have a good way of lining them back up without using the Telco meter/guage? Ive been told that the...

Hello all, Just want to share my negative experience in dealing with this company. I bought a refurbed vending maching (and would arrive like new) in December of 2012. Was told I could have the machine within 2 weeks or so. Turns out it was close to 2 months . The machine came in with some...

Hello all, I have a Coleman electronic 8 selection vendor that has been giving me fits the past 2 years or so. Ive had the electronic board repaired 3 times and just everything about it has become very unreliable. I would like to get a full size vending machine maybe 39-52 selection. does...

Hello all, The tire cleaner is bubbling air back up into the tank. Ive replaced both regulators and cleaned out the needles on all the solenoids. The procon pump is running dry and wont stay primed because of the air pushing back through the lines. I think it may be a bad check valve in the...