Search results

Conveyor speed fluctuation. Is it only under load or with or without cars? Did you adjust the Torque (Not speed) control on the power pack? HAs the issue existed from Day one on the new one? Did you use any old parts like the speed / torque control? Does issue vary with temperature?

Your controller scree somewhere should have a flashing item or counter for the pulses. Since it works on simulated pulse it would seem the controller is not getting the signal from the pulse switch. If all connections from the switch to controller are good you may have a bad switch. Even if...

That is how I would do it - No Guarantee only the gun gets hooked. Hoes could get caught n something. Yes you could lose the length of hose and gum, as opposed to the entire boom could getting ripped down.

I could only suggest 8. I figure if you put one in the center it will do more between cars where you don't need it as opposed to down the length of each. I guess you could experiment if conduit runs down each side wall. Try 3 on each and see how it works. If not ood switch it to 4 on each sidewall.

My Erie Hog hair last about 6 Months . Years ago at request of Dan Pecora. tested against univerasl in half the bays.. Erie was better.

Are you saying you noticed something a year ago and still got another year of use out of them? How long did they usually last before you had this issue?

I suggest you call Erie and ask to talk to Jason Ugent (the boss) - he seems very responsive.

Assuming it is a "Flow Divider" to feed multiple Speed / torque controls? Never rebuilt one except to scavenger parts of some bad ones I had to make one good one. Also, once had a 4 bank go bad on a busy day so I put together pipe manifold to feed 3 banks and never put back a flo divider...

Added Cryptopay some years ago. Already Had Dixmor LED timers so I did not have to change that for the bays. They only use Worldpay for processing. I had added boxes for Bill acceptance s I put the swiper on those boxes. ( I corrected $ programming after video was shot)

If by "Hub" you are referring to the Piece that goes on the shaft of the brush that holds the cleaning material - Erie Brush makes hubs.

Like asking if I would rather slide a mile on a razor blade or suck on a dogs nose until it's face cave in.

what type of controller are you using? IS the "Latch" the switch that shows the care entering the system "Sometimes called "Enter switch" or "Gate Switch" Switch / Eye / loop is faulty or connection is. . Your controller my or may not have a built in work round called "Simulated ......." so...

Slightly off topic but years ago I replaced my fragramatics hose with Coleman assembles. Much more durable. Then I learned I could use coil wrap hose protectors and they never wore out where they rubbed - Just dry rot after several years and I could re use the coil wrap when that hose was...

https://thisvsthat.io/fluoride-vs-fluorine Aside from limits on concentration of Fluoride and RFK jr. I find nothing about compounds being formed (Unless you confuse Flourine with Flouride) I would b interested in any link to a source (not RFK jr or general anti vax conspiracy related )...

I went simple route of adding a boz for Bills and later used that for CC Swiper. Did it for a couple reasons. First did half the bays to accept bills to make sure investment in boxes and acceptors was worth it. Also figured if they attacked the bill box the main box would still be in...

Yes, but even if lol regs / enforcement were tied to the hammer of Federal funding, I don't see local regs changing just because Fed regs get loosened. Possible - Yes. Likely - No.

OP says it was the local health dept. Reducing Fed regs won't necessarily affect their regs. Everyplace is different.

Whatever they do would likely only apply at the Federal level and would not apply to a state or local agency.

I was advised to use single wire braid 3/8" hoses when I too over a SS because it would not kink and stop the weep as other hose might. Never looked back

I tried to schedule a monthly shot of WD 40 in all locks. Many "Lock People" do not like this but it seems to flush out junk and corrosion and keep things lubricated.