Search results

I’ve had good success with Quest 4WD Hi – single step Pre-soak. Titration at 20-25 drops? Air-assisted application? Streaking could be due to excessive Pre-soak volume and low air pressure. 4WD Hi works best with warm soft water.

As soapy says... A #6 screw extractor works for 3/8" fittings. Here's an inexpensive 6 piece set from Ace Hardware...you'll likely never use them all. Irwin Hanson 19/64 in. Carbon Steel Spiral Screw Extractor Set 7 in. 5 pc - Ace Hardware

Nearly all of my customers dispense $1 coins from their changers. With MicroCoin acceptors in every device, they also accept customer's quarters. I converted to $1 coins in 1999...with $3.00 to start the bays. That didn't stop the customer's quarters from pouring in. Instead of regularly...

All of our installations are quietly awaiting this weekend's forecasted 20ish degrees. Our pre-season freeze protection and floor heat system tests were completed last month.

Puzzling...All of my Nayax VPOS installations use the car wash’s 24 vAC tranformers. No smoke! To have VPOS to serve as the Bay or Vacuum’s timer (providing steady 24 vAC output to the load) one can utilize a HiLetgo 5V One Channel Relay Module (or similar) from Amazon. Position the relay...

You can use winter formula to protect your brushes. For triple foam guns to work properly in freezing conditions consider this: Water weep will dilute the product. When the Weepmizer turns on the water the tri-foam product will be diluted and quality delivery to the active gun will be...

slash, I haven't had any issues using 1/4" poly for washer fluid lines. 2Biz and I have agreed to disagree about this. LOL 6 bay system for foam brushes and foam guns

2Biz, Thanks for the acknowledgement. It’s astonishing how long it’s been since we worked on your system. My current version takes advantage of Sieman’s/IDEC advancements in the SmartRelay platform…specifically it’s networking capability. Several SR can now be networked to provide expanded I/O...

Pulsation and pressure fluctuations are typically caused by air leaks in the pump's supply plumbing. Since this issue exists when only when soap/wax/presoak are selected I would suspect a loose fitting, or a cracked product hose.

Rowe’s counter is the “Value of the bills accepted…not the number of “Bills Accepted” $1 bills advance the counter 1 number. $5 bills advance the counter 5 numbers, etc. If the counter is providing incorrect information, I would consider replacing the counter.

I think he's talking about the repressurization pressure/volume.

Yes...with an uninsulated 4" overpour on top of the existing slab.

We’ve always spec 4” of 4000+ psi concrete on compacted base. We install 1/2” O2 barrier PEX over 3” foam insulation (Crete-Heat). The contractor must lower the finished grade to accommodate the new finished floor elevation. Side note: Concrete must have been really cheap in the late 70’s...

:) We are the local company.

Contact https://carwashboilers.com/ Chris & company can supply everything you need… Oxygen barrier Pex tubing Manifolds and Boxes Lochinvar Boilers and Grundfus Pumps System design I use https://crete-heat.com/ for under slab insulation…spendy, but saves a ton on operating costs. Without the...

Apply tape/dope to NPT fittings only. Do not apply tape or dope on JIC or “non-working” swivels. The tape/dope prevents the tapered faces from making full contact. And, always remove the wad of tape from a reused fitting. You’re welcome.

Here's the only electrararanic info on Timemaster from the manufacturer and the original master distributor. Coleman's 1034 is their version of the TM5. FIELD PROGRAMMING PROCEDURE (hpws.com) https://www.hpws.com/techfiles/TimemasterManual.pdf TM5-CT2000-Programming-Instructions-Updated.pdf...

We have several suppliers in the metro area. These are our favs. Marmon Keystone Titan Fittings

With several dozen trough systems installed, these are the only photos in my library. Equipment room roof penetrations are made with 4" hole saw and electrical nipple, nuts, and bushings. For bay penetrations, 3/4" PVC conduit slip x MPT adapters, lock nuts and bushings.

DH is no longer. Look here... https://rpdvending.com