Search results

Can this be used with crypto??

7/16" socket and 7/16" wrench. That's all. The hydraulics are pressure fit on the cover.

Is it possible to integrate this with an ACW and Cryptopay? I have no idea how it works, but the concept is cool!

Could be a faulty impact switch, cord, etc. If you have a t-bar sensor for impacts, it could be that as well. 100#1# and get a fault message. This will help.

Folks, I have learned a lot from you over the past few years and am very grateful! I have a Lexair Valve on my undercarriage for my LW4000 that is starting to leak. An indication that it needs to be rebuilt. It is one of the "4 bolt" bigger lexair valves. I have one of each on my pump stand...

Hello! My Laser is operating very well! I seem to be in nit-pick mode. How much slop/wiggle should the spray arch have when it rotates 90 degrees? Mine seems to wiggle a bit after the turn. It is not a tight turn. Just curious how yours operate. Thanks!

DUH! Sorry. It is the motor to the centrifugal pump. I'd like a replacement assembly for the whole motor/pump assembly. Sooo sorry! Thoughts?

Hello! I have an LW4000 with SFR delivery pump and a GinSan Water Lovers RO system with a 5 bay SS delivery pump. I believe, both pump motors are the same(I attached pics). If I am wrong, please let me know : ). Single Phase, 2 HP. Anyway, I'd like to have a back up pump/motor assembly on...

White is on the entrance side of the trolley. Black on the exit side.

White have tighter tolerance to the rail and acts as a guide to the bridge/trolley, I believe. Black functions just as a roller.

LW4000 gurus, How long would you say that the Telemecanique x30 switch lasts under normal use? Average 15k+ washes a year. Just wondering. I started getting a L/R count error in the VT. Once every few days. Starting with the x30 replacement and working backwards. Thanks!

Folks, I rebuilt my old neglect LW 4000 trough yesterday. Insulated with 1" foam board top, bottom and sides. Two layers on top. Constructed from pressure treated lumber with PVC cap and drip edge. Sponge foam weather stripping around the hinged doors. On a slab, flat roof. Needless to say, it...

Yes. Slab roof.

Hello! I have a LW4000 trough made from treated lumber. 17 years old and needs to be replaced. What materials do you recommend for trough reconstruction. I was going to rebuild it with treated lumber and cap the top with pvc and vinyl trim for water tightness. Any advice??

I believe I run both air and soap at 40 psi.

Update: Swapped all boom hoses and spray gun hoses today. We will see if there is a change. Time will tell.

Folks, I took off the line to the bay and connected a new hose. Sprayed water in a clean 5 gallon bucket. Clear water. Hooked back up to the bay and sprayed water from bay gun into a clean bucket. Definite suds. I guess I'll start by getting the old Neptune 3000 boom hoses and hoses to the gun...

So I did a few tests. One, sprayed the water from HP rinse into a bucket. You could see the little bit of foam initially. But it would go a away. When it did go away, I agitated the water and it didn't really come back. Also, my spot free TDS reads 9ppm. Thoughts? Am I going crazy ; )?

Well, The initial complaint came from a customer washing his car. A regular who is familiar with the wash. I have used a bunch of surfaces, including the floor...Dohhh! I do have Neptune 3000 in the boom. Swapped it out without any change. Gonna move to the trough hoses next. I am also letting...

Folks, I have a problem that is very similar to the one in this thread: Soap in HP Rinse This is what I know: When I use HP rinse there is a very little bit of what I think might be soap in the HP rinse. Can see it on the edge of the water when sprayed on to the bay floor. All 5 bays. I...