Search results

I actually have the Rowe working now. It just needed new LED lights on the coin detectors. Actually just one was out but I replaced them both. If you want to buy it in working condition send me a message.

Im in (y) looking forward to connecting with ya'll

If you get it at a discount theres almost always an opportunity. First discount I am asking for is for the electrical work because it looks like some crack heads stripped your wire out of there.

Your blue hoses run product and your white hoses run air. Find a place (regulator or shutoff valve) to turn air off to the bays and then run your tire shine and see if its pulsing without the air. If it is then your issue is on the pump side if it is not pulsing you should build up a foam...

You may want to move your question to the "In Bay Automatics" forum. This is for self serve discussions.

Your bank wouldnt know how to run your business if they had to take it back so to them its not valuable doesnt mean someone else wont see it as valuable. Credit Unions seem to have a higher propensity to underwrite loans based on potential and look at the big picture.

I picked up these change machines from a car wash that was closing down. Rowe BC1400 Hamiltion DRS-CRC The Rowe has a Mars bill validator in it but I cant get it to clear the 2 blinking red light error also on the board it reads an error "Check L Coin Detector" The Hamilton seems to be...

Thank you all for the feedback on the system. It sounds like the common denominator is try different tip sizes. I am currently on a 5040 tip and like you mentioned @cantbreak80 It hits the protector and drips off the gun. Also appreciate the history lesson on Southern Pride. The build on it...

The video I made of this is kind of long because i included the entire installation and etc. so you can kind of skip to the end of the video. Ultimately I am looking for any additional tips on how I can make this Triple Foam the most satisfying car wash experience out there. I have already...

I have this same issue did you try a different tip like MEP mentioned? I moved the pump to a different bay and it followed the pump which makes me think its something on the pump. Mine drops to 800 PSI just like your saying.

Noob, MEP, and Old Town Thank you for this thread I was just about to fire up my whole system this evening but it looks like I better consider the phasing before I do so. I am hooking up a used Southern Pride triple foam to my CP pump stand it seems to be very similiar to what you did. How did...

Im looking for some more advice on this triple foam unit that I also have pictures of above. I finally got everything hooked up and turned it on but the pump wasnt pulling anything and when I pulled off the hoses for the supply side there was barely a trickle of chemical. I took off the 3...

Although quarterly may be the minimum I would think daily is excessive on the other hand. I dont anticipate my water softener to completely fail overnight. A water softener may become less effective over time and the hardness of the water should be monitored but I use other indicators as well to...

Try increasing air first. If you can get the consistency there then you may be dilluting your foam brush chemical too much. Increase your tip size a couple notches in that case. Last thing to look into is that your water softener is working properly this is a good thing to test once a quarter...

Hi I am looking for some help on how to wire in this used triple foam unit I bought. The first picture below is my Carolina Pride Pump Stand and the second picture is a used Southern Pride Triple foam that I wall mounted next to it. My question is where in my pump stand should I pull the 24 VAC...

Hey Walter White! Take your card to the Nayax reader and attempt to tap. You will get an error because your prepaid cards are not added to your system. Now go into your back office Operations>Machines now select the machine you tapped the card you want to program on. Go to the Info tab>Last...

I was so confused until I started reading WTF

Is yours not fully closing on shutdown? Thats what mine has been doing and then flooding the dang equipment room. I dont use a lot of RO water so I turn the system off once its full and refill it whenever my storage gets below half. Its a pain and want to get my valves fixed too.

I am wondering what other operators do to maintain your plumbings and hoses in a somewhat organized and aesthetically pleasing way. I am somewhat meticulate on how things are run so that its easy to follow and diagnose down the road. I am adding a triple foam unit to this setup and I need more...

Looking forward to hear how adding those readers changes your revenue. My car wash was not operating when I took it over so I had no previous data but I can tell you now that 70-80% of our sales is through credit card.