Search results

I suggest you call Erie and ask to talk to Jason Ugent (the boss) - he seems very responsive.

Assuming it is a "Flow Divider" to feed multiple Speed / torque controls? Never rebuilt one except to scavenger parts of some bad ones I had to make one good one. Also, once had a 4 bank go bad on a busy day so I put together pipe manifold to feed 3 banks and never put back a flo divider...

Added Cryptopay some years ago. Already Had Dixmor LED timers so I did not have to change that for the bays. They only use Worldpay for processing. I had added boxes for Bill acceptance s I put the swiper on those boxes. ( I corrected $ programming after video was shot)

If by "Hub" you are referring to the Piece that goes on the shaft of the brush that holds the cleaning material - Erie Brush makes hubs.

Like asking if I would rather slide a mile on a razor blade or suck on a dogs nose until it's face cave in.

what type of controller are you using? IS the "Latch" the switch that shows the care entering the system "Sometimes called "Enter switch" or "Gate Switch" Switch / Eye / loop is faulty or connection is. . Your controller my or may not have a built in work round called "Simulated ......." so...

Slightly off topic but years ago I replaced my fragramatics hose with Coleman assembles. Much more durable. Then I learned I could use coil wrap hose protectors and they never wore out where they rubbed - Just dry rot after several years and I could re use the coil wrap when that hose was...

https://thisvsthat.io/fluoride-vs-fluorine Aside from limits on concentration of Fluoride and RFK jr. I find nothing about compounds being formed (Unless you confuse Flourine with Flouride) I would b interested in any link to a source (not RFK jr or general anti vax conspiracy related )...

I went simple route of adding a boz for Bills and later used that for CC Swiper. Did it for a couple reasons. First did half the bays to accept bills to make sure investment in boxes and acceptors was worth it. Also figured if they attacked the bill box the main box would still be in...

Yes, but even if lol regs / enforcement were tied to the hammer of Federal funding, I don't see local regs changing just because Fed regs get loosened. Possible - Yes. Likely - No.

OP says it was the local health dept. Reducing Fed regs won't necessarily affect their regs. Everyplace is different.

Whatever they do would likely only apply at the Federal level and would not apply to a state or local agency.

I was advised to use single wire braid 3/8" hoses when I too over a SS because it would not kink and stop the weep as other hose might. Never looked back

I tried to schedule a monthly shot of WD 40 in all locks. Many "Lock People" do not like this but it seems to flush out junk and corrosion and keep things lubricated.

If you are mounting in block avoid anchors and bolt them thru the wall with Fender Washers or a steel plate on the other side or back to back if using 2 and the bays will accommodate that and consider using Stainless all thread, nuts and washers

If I tried to call in sick there would be no one there to answer the phone. But luckily with n 8 Bay Self Serve and 3 changers there is some redundancy.

1505 all year

If the bags are that new and motors are sucking in trash you have a bad seal around where bag is installed. or a hole in a bag allowing trash to get to motors . Otherwise that cannot happen. I would also suggest a screen below each motor but if you are bypassing trash that will get clogged...

I use the hose clamp but take a slightly larger piece of hose about 2 inches s long and slit it lengthwise and put that around the hose with the hose clamp over it. Keeps the clamp from cutting thru over time - then again if is too secure and gets hooked.....

Many different system out there so hard to advise. MIne had a separate line from the soap tank to an injector at each pump. Each line had a screen filter in the tank. When HP soap was chosen a solenoid at the tank would open allowing soap t flow to the injector. So, you could have a clogged...