Recent content by petitemoose

Got It! Nevermind :) I called Ryko and they answered the questions I had in a very friendly way. FYI it is called a Ryko Soft Gloss XS machine and the assumptions I made were incorrect! If anyone is interested I can post the correct way to wire it, otherwise ignore / delete the thread since...

Gov't Rational Thought and common sense has no place in government and especially building inspectors and or code enforcement. This being said, You cannot use intelligence or any type of rational thought if you hope to get anywhere. The ONLY thing you can do is beat them with a conflicting...

I've got the wiring diagram from the Ryko specifying where the wires originate from and Hamilton tells me that I am to terminate on wash packages on A1,2 3,4,5,6, B1 and 2 then C5,6 for the Wash in use signal. Ryko terminal numbers are G 90,99 ( Ground Neutral and Hot ) 4, 19,21,23,25,35,92. I...

We tried the local dealership route as well. It seemed to be a natural fit and a wonderful fit. The used lots ended up not paying their bill for 90 days and wanted complete details for $4.99 exterior washes. Endless threats and never satisfied. We even had one guy come in and claim we stripped...

Sounds like one really expensive fuse!

It also sounds to me as if you are applying dressing to a dirty tire. The goo you are getting is the grime the dressing is removing when being rubbed onto the tires. Clean the tires before application and you'll get much better results and a "goo" free car. I can attest to the results of the...

Out of curiosity, is there a reason you aren't considering Ceccato Equipment? They are on your side of the pond being based in Italy. They have tunnel equipment already spec'd to european voltages and procedures.

Actually, I was having a problem with my Dodge a few years ago and I Did call Detroit. They patched me through to their 5 star customer service department that were more than happy to help me out. My question was answered and my truck was fixed with genuine Mopar parts. You see, that's a sure...

UPDATE ... I received an e-mail they released to the press and it contained one very interesting sentence: "Right now we cannot even legally take our vehicle that has our PICC installed on the public highways." I think they may be on to something, but until it is tested and proven, I'm...

The freestyler does not have a VPS option. I went to their web site and ran their Freestyler Configurator and the VPS is not an option. Looks like your gonna have to suffer through the stupidity of the elderly American Driver like we do during snowbird season during the winter here in Florida...

The easiest future prevention tip I can give you will cost you about $20. Go get two tubes of DiElectric grease. Take the plugs apart and fill both sides as best you can then re-connect. Smear the excess around the outside and into the grooves. Repeat on the next plug. This will prevent the...

I also thought that having the spray arm "tilted" it would help remove the dirt by adding an extra bit of "friction" and also add a reflective quality to the rinse process getting the water off the car a bit faster. My buddy said it "looked bad" and would rather have it straight. So, I...

Will Do. I am replacing the Prox Target "T" for the dryer as well. It was rusty and thin. I think the biggest improvement I can make is to set the prox switches closer to the targets. Right now the gap is an incredible 3/4" away. I've always set up the prox switches to be under 1/4" from the...

VERY good question! I approach every install, no matter what the machine is, with the goal of installing it so it can do the best possible job that it is capable of doing. Every machine has it's strong points as well as weak points. Since I sell nothing ( until very recently) I had no part in...

NHT Isn't the only one seeing your point. Not only do i see your point, I've been doing exactly what you're proposing for almost a decade. I am a "free lance Installer" as well as Distributor for machinery and chemicals. The latter part of my qualifications have just been added as the install...