Search results

I purchased a wash with a Unitec WashChange machine. I prefer to dispense dollar coins so I tried converting it. I have done it twice before on other Unitec changers with no issues. When I change the dip switch setting to dispense 1 coin per dollar instead of 4 coins per dollar, it doesn't...

Added credit cards and space for more functions. Disclaimer - I did not let my wash get this bad, it was a wash that was purchased this way.

I am purchasing a wash that currently has a PDQ Access. Does anyone know what the process is to get a merchant account setup and switch over to a new owner?

Cryptopay swiper is flashing yellow and the upper display screen on the washselect is blank. I'm not too familiar with cryptopay. I have powercycled everything. Anything else to check? I left a message with support. David

I have a Ginsan RO system that is about 20 years old. It began producing water at a trickle so we checked flow controls, water pressure, regulators, water filter. Finally put new membranes in and it worked great again. After 2 months, it was back to a trickle. Installed another set of new...

I'm not familiar with Purclean systems so this maybe an obvious answer. My unit keeps shutting down with this error message: "Excessive pressure switch trips Unit off!" Any suggestions on what to check? I'm not sure what pressure this is monitoring David

I have a Ryko Softgloss that isn't applying presoak. It doesn't seem to be injecting the presoak into the water stream. The blue-white pump is pumping and I checked the injector/check valve and it looks ok. Is it possibly for a Blue-White to pump product when there is no back pressure but not...

I have a 10 year old Softgloss. When the top brush comes down on the back of cars, it stays down and the machine aborts the wash. It washes SUVS with no problem, it only fails when the brush lowers on the trunk of sedans. Any ideas what the issue might be? David

I need some help from guys that know the Ryko Softgloss. I am having two issues that I am sure are the same cause but not sure what the problem is. Occasionally, the wash ends and the drive through blowers will start and immediately shut back down (3-5 seconds) The customer hasn't even had...

Has anyone had issues with Aquamaster floats sticking open? I don't know if that has ever happened with my Hydrominders but I have had 3 aquamasters stick wide open. Just wondering if anyone else had the same experience. Planning to switch to Hydrominders. David

Long shot... Does anyone have a spare Softgloss rear brush shaft within driving distance of PA? Ours got bent today and I don't have a spare on hand, neither does the local distributor. I am located in central PA and willing to drive a few hours to get it. David

I have a Ryko Softgloss (about 10 years old) that is not spraying Presoak, brush lube or spot free. Triple foam is working. What should I check? Still trying to learn this machine. Thanks

I have a Ryko Signature Series pump stand from 2009 that I am working with at a wash I just purchased. The current issue that I am working on is water pushing back into the tanks which dilutes the products. This unit has a HP soap tank, HP clear coat conditioner tank and HP wax conditioner...

I just purchased a wash with a 10 year old Ryko SoftGloss. This is not a machine I am familiar with so I am trying to get up to speed. It has a few issues that need to be corrected to get a quality wash. Does anyone know what size spray tips are supposed to be on the machine? Most of them...

Has anyone ever converted a lube bay to an inbay automatic wash bay? I'm thinking it would be fairly complicated and expensive.

I have a Laserwash 360 with a HTCK4050S General pump. It is leaking water out of the bottom of the pump. Does anyone have an experience rebuilding them or is it better to replace completely? David

I have an occasional issue where my WS2 will accept payment but the signal to the inbay never gets sent. It seems to happen only on one wash package. I know it isn't an issue with the wiring or the inbay automatic. Is there a relay or something in the WS2 that could be failing? David

One of our floor heat loops isn't melting the ice, this particular loop is for the concrete outside the entrance to our automatic bay. Where the return side of the loop connects to the manifold it is cold when all the other return lines are warm. Is it possible to get an airlock or something...

We have a Unitec WashSelect II that is occasionally (3 times in the last 3 months that we are aware of) dispensing 40+ dollar coins. On one occasion is was only supposed to dispense 1 and gave the customer 44, yesterday it was supposed to dispense 9 and dispensed 46. I can't replicate the...

I have three Wash Select 2s and I don't think any of the heaters are working. It appears that there are three parts to the heating system: a thermostat, a fan, and a heater assembly. Should I order and replace all three parts? Is there a part that is the frequent failure point? Any tips...