Search results

  1. S

    Hamilton HTK- nonstop issue- Transaction in progress

    It sounds like it may be the wash in use relay on your machine. Knowing which machine you are activating will help in the troubleshooting proces
  2. S

    Old Airlift Doors circuit bd PN?

    You have to buy a new motor and control box with vfd. Last one we sold was about $2200 + install but I am sure they have went up.
  3. S

    Old Airlift Doors circuit bd PN?

    I have a used one on the shelf. $50 would take it home. I was not aware you could still buy a new one though. I would go that route unless they are just stupid. I agree with others that the new style motors from airlift are the way to go. Pricey though.
  4. S

    water/freeze/co2 detection

    We use the ring alarm/camera system as an add on to our camera system. We added the water detection sensor and have a couple of cloud based cameras. Added these after a break in where we had the DVR stolen. The water leak detector has been a great add on though to be notified for a leak. It...
  5. S

    2010 vector rapid carwash

    What state are you in? A belanger distributor should be able to get a manual for you.
  6. S

    Spot Free Pressure

    Sounds like either a bad pump or air locked. I have seen rotation be backwards on the pump and get low pressure like that. Is this a new install?
  7. S

    How do I open these?

    It will pry up. 2 Flat blade screw drivers is best way i have found.
  8. S

    Airlift 208v 3 phase door issue

    I do not know of another source for those boards and I have looked. We have had to replace many of them with the new style motors and control box. As far as your issue, I would pull that cover off the motor and call airlift tech support. It is most likely the safety eyes or the button.
  9. S

    New technology advice on Surveillance Cameras

    Speaking of Lorex, has anyone figured out a good solution to cloud storage? We were broke into last week and of course they stole the NVR. We are now adding some layers of security. I have a new NVR on the way and added a couple of ring cameras to the site as well but would really like to...
  10. S

    Tokens

    Have you tried IDX? The tokens we use from them have been readily available the past year and just ordered and received a batch last week.
  11. S

    Do you have flood insurance on your wash?

    No I do not and I would place some pressure on the lender to avoid this requirement. I have had a couple of lenders on a couple of different properties try to force flood insurance on me and avoided each time. Many times the flood maps are out of date or just plain wrong. On the other hand if...
  12. S

    Super 5000 troubles

    They don’t sound related. The limits on that machine are detected on the floor of passenger side. There are two pieces of metal on floor, one at entrance and one at exit. Make 100% sure there is not a piece of metal somewhere on floor. Run the machine to front and rear and make sure prox is...
  13. S

    Super 5000 troubles

    Is your floor limit prox working correctly? There are no magnets or metal laying on floor in the path of the prox right? . I have done a few service calls and found a bolt or magnet laying on floor causing machine to be confused. Check the carriage encoded as well. It seems like that was...
  14. S

    Super 5000 troubles

    Are you saying the carriage or the gantry runs to the end of the track? Does it happen on any wash package? Programming been changed?
  15. S

    Magic Wand C6100

    We changed those to flojet pumps over the years at all locations over the years. They work just fine but you loose the ability to recirculate hot chemical out to the machine. I can't imagine saving any money on power swapping that motor out to 3 phase.
  16. S

    D&S 5000

    I will be pulling one out in a couple of weeks in southeast missouri. Would be happy to load it straight to your trailer for $10,000. It is still open and washing cars for the next 2-3 weeks. Feel free to call me at 573-979-3423. (Steve)
  17. S

    Super 5000 troubles

    That gantry encoder never seems to be the issue in my experience as long as it is counting forward and backward with similiar results forward and reverse. Is your sonar still active or have you tied it in with the safety eyes? We did that a couple of years ago with no negative affects.
  18. S

    Super 5000 troubles

    Just curious, did you ever find a solution. I have a couple of these super 5000's that we fight every once in a while. Tough to find anyone with any expertise on this machine. If you havent figured out I can suggest a couple of things to look at.
  19. S

    Unitec Wash Select Batching Issues

    Unitec recommends only a plain old telephone line for dial up. We fought a VOIP line for dialup for a year or so before we gave up and installed a traditional line. Problems went away. On another note, if this is even a remotely successful site you should go ahead and upgrade to high speed...
Top